Showing posts with label mount. Show all posts
Showing posts with label mount. Show all posts

Tuesday, October 25, 2011

E36 M3 Front Suspension Overhaul Part I: Front Lower Control Arm Ball Joint and Bushing Replacement

So after the last track event, which was years ago it feels like, I was experiencing a scary 'knock' noise in the front suspension upon heavy braking. It felt like it was in the steering or at the very least something part of the front suspension.

I got the car home and have been doing a major overhaul and the front suspension replacing anything and everything down there. I'll do a 3 or 4 part installment of everything I went over. First up is the front control arms.

95 M3 Control Arm
With 150k miles on the chassis I was positive the front control arm ball joints and bushings were shot. I would also assume they are the factory units having bought the car stock from a non-enthusiast. The easiest way to replace these is just order new control arms with the ball joints alrady pressed in. Unfortunately these are about $200 each for Lemfoerder brand control arms. The Meyles are slightly cheaper, but I would only go with the Lemfoerder personally.

I then discovered that you can press out the existing bushings and use Lemfoerder ball joints from the e30 control arms. The topic is covered in this thread here. So for about $25-$30 a ball joint you can replace all 4 for about $120 instead of $400. Also I decided to change my tie rods and sway bar links since they were shot as well.


Removing the control arms is no easy task. First to get more room I removed the sway bar.


Then remove the nuts on the top of the subframe and the other one on the spindle. Keep the lolipop with the control arm bushing attached to the car for now unlike the picture below.


After that I used an arsenal of tools to remove the control arms.


The control arm ball joints have a tappered fit which creates a mechanical weld. You need a pickle fork to break this weld. My ball joints were so stuck I used a torch to heat them up, an impact air hammer with pickle fork adjustment and a 4lb hammer just to get the force I needed to break them up. In the end that wouldn't even work and I ended up using this guy.


All these tools were purchased from harbor freight and, honestly, did the job. When the welds break it will go off like a gunshot. There is no other real DIY for this, it's just removing bolts and brute force. The ball joints themselves had some play in them but they were snug in their homes. I tore the boots upon removing them but the control arm ball joints and tie rods themselves did not look responsible for the knock noise I was experiencing on the track.

Once the arms were both out I took them to my buddy Justin Pawlak's shop Hotline in Gardena. Justin and I grew up in the same town and when he's not busy winning Formula D races I ask him if I can borrow his tools. ;) I didn't bring my camera so I don't really have any pictures of the process. If you look at that thread above you can see you'll need a 20 ton press at the least. That is what I used. Here are the old ball joints pressed out.


Justin, rushing at the time building badass drift cars, pressed in the first set showing me how to work a press and accidentally tore one of the boots. I pressed in the other arm and replaced the torn boot. I couldn't order just the boot so I bought a $11 Meyle ball joint and salvaged the boot from that.





I also decided to use Delrin front control arm bushings. The set I used is the TC Kline/Turner Brand. Since they are offset of the 1995 M3 only they need a set screw so that they won't move. A simple tap and they were set.




So that's about it for the control arms. Up next is subframe reinforcement followed by steering rack swap with new tie rods.

Monday, August 29, 2011

E46 Rear Shock Replacement Michigan Car

So I had the pleasure of helping my buddy replace his blown out rear shocks on his e46 323ci. Having come out from Michigan I knew we were in for a couple surprises, luckily nothing that couldn't be remedied.


The lower shock bolt was slightly rusty but nothing too terrible that I hadn't already been through with my own experience on Michigan cars. It came free with a blast from the impact wrench. The area I was more worried about where the shock towers and they were clean as a whistle. The same could not be said about the factory shocks.


This is what a happy Indian man looks like knowing his car will soon handle again.


Ohhh yeah, how I don't miss that. Here's a nice side by side of the replacement Bilstein Sports.


We ran into a little snafu with the shock plates that hold everything together. They had take a beating as well. We figured it would be pretty stupid to put the old rusty plates on the new shocks so we headed off to the only BMW dealership that was open which had the plates in stock. After a $38 ass rape later for some little metal washers, essentially, we were back to finish the install.


If you're reading this wondering how to install your shocks, it's simple. Pull back the carpet in the trunk. Release the lower bolt but put something under the tire so the suspension doesn't completely fly around. Take the two lock collar bolts off the top that mount to the body and you're done. Put the new shock mounts on shock by holding the shock with some pliers and tightening the nut down to 10ftlbs. Which is just slightly tight.


Don't forget the reinforcement plates which can be ordered from just about anywhere including BMA Parts where Mathew bought these. We had to put the rear shock mounts in first then the shock, but however way works for you just use a new locking nut on the top. Torque the body mount nuts down to 17 ftlbs and the bottom bolt to 57 ftlbs. 

We went with the Meyle HD shock mounts which I'm running on my e36 and have been happy so far. The JT Design or after market rubber bushing styles clunk from what I've seen. Here's a picture of the factory shock about the shear off at the top.


Not only were they rusty blown out and destroyed but they were leaking too.


Phew, just happy to see those out of there, as well as help another fellow enthusiast out. I guess it's on to the fronts next!