Wednesday, February 10, 2010

1/30/2010 New Tires and Power Steering Inspection

So I signed up for a NASA HPDE event for Willow Springs on February 7th. In doing so it made me speed up getting a few items on my car taken care of. For one the rear tires were shot. The old ones were Sumitomo HTR + which had worn down in the middle. I don't know if it was too much tire pressure or just the way those tires were. Either way my car was sliding around in the rain and would snap loose in first if you gunned it. Sooo Nitto INVOs to the rescue!


I picked the INVO on recommendation, looks and the fact that they're designed for quietness on the road. Vic from eurowurx seemed to think they were the best bang for the buck and I guess he goes through a lot of tires. Also they're supposed to be super quiet. Figured I'd try them out. The last tires I had, BF goodrich T/A KDW 2, sounded like a dune buggy on the highway. Loud tires suck. At 260 tread wear they're pretty sticky. I found a place on ebay that had the 245/40/17 for $130 shipped each. Best deal I could find and they compete with the much more expensive Potenze and Pilot street tires. For a street tire they looked pretty cool and turned out pretty nice. The PO had 245s on all 4 corners. I don't think I have 8.5" all the way around. He Probably just stuffed a 245 on a 7.5 inch rim.

On the way to get them mounted I picked up some much needed wiper blades. The icons were 25% off! Can't beat that! Look at those babies!


I took the car over to discount tire in Glendale to get the tires mounted and balanced. They guy said $20 a tire. There were about 40 tire shops on the street. I said the guy down there told me $15. I Gave him $30 and succumbed my anxiety of handing it over to Glendale's finest.

As you can see the rears were pretty effed up.


Balanced.


Floating M3 pic.


And new tires with Carlos. Tires look a little beefy, but I'm ok with the track as long as the sidewall holds up. Car was pretty dirty from its latest trip to Big Bear. :D


While the car was on the lift I took the time to get under there and check everything out. Not being a California car i was worried about rust, but I can't seem to find anything that would resemble what I'm used to from Michigan. I focussed more on my power steering leak. It looks like it's coming from everywhere.


The droplets on the sub-frame are from the car wash. That's not from the leaking. And yes that is the "darker gray" colored 95 M3 rack with 3.0 turn Lock to lock. I'm not even sure about all this steering rack bull shit anymore. Now I've heard the 95 rack isn't fast at all. I don't know what's right with the z3 rack and the regular blah blah blah...i mean jesus, so sick of what rack is fastest. All I know is that this car's turning radius when stopped or parking is crap compared to every single other car I've owned and driven. What's that mean? I mean I have to make more points when turning around. The rack just does not extend enough. I haven't driven other e36s or the z3 to comment any more from experience or comparison.


The steering knuckle and driver's side motor mount are just covered in fluid. I'm thinking now the seals in the rack are gone, but I'm going to try just the lines and new crush washers and see how much it stops.


Passenger side looks pretty clean. I believe there is only the main housing seals out that way though. So only one area to leak.


You can see here how the previous owner tried to fix the leak from the return line with a new hose. That hose clamp is supposed to be a "hard" clamp. The part is one piece from the rubber to the cooling line. I think the method shown works and saves money, but only if you get the reducer and clamp that down in the middle of the rubber hose. This hose did not have that. It was leaky. Tomorrow I'm going to try and remedy a bit of the P/S system.

Friday, January 22, 2010

Fuel Filter Change 1/16/2010

Mileage 136,900

While I was under there changing the oil, I decided it would be a good time to change the fuel filter. On the 1995 e36 the filter is located under the car on the driver side, underneath the door. I read a tutorial about how to change the filter and the kid spent about 12 photos on how to remove the rusted nuts. Even though my car came from Virginia, by way of Texas, by way of Maryland, there was luckily no rust on the undercarriage. This was the one thing that I worried about when I went to buy my car in SD, but the guy said it had never been driven in winter and so far I don't see any signs. On to the filter change.

So it's not bad at all. Here you can see the filter cover over the fuel filter. It is held on by one 10mm and 8mm nut. Also before removing the filter remember to light a cigarette and talk on your mobile phone! Or instead, disconnecting the battery doesn't hurt.


You can pinch the outsides of the cover together to remove the plastic tabs from the body. Here's a pic of the cover removed.


There is one more bracket holding the filter up. It's held in by a 10mm nut. You have to swivel it down for the tabs to come free from the body. I was able to remove it and put it back on without too much trouble.

When disconnecting the hose clamps from the old filter you can clamp down on the rubber hoses if you'd like. I had a pan for the excess fuel and filter drain off. Most of the fuel is in the filter itself. There was more fuel in the hose going toward the front of the car. I left a clamp on that one and the one towards the rear was dry pretty fast.


Pic of the new filter ready to go in.


When installing the new filter make sure the arrow points to the front of the car.


Here we are almost done with the install. You can see the clamp on the rear hose. When I removed to connect the filter, most of the fuel had already ran out! So the fuel left over is minimal. Once your new filter is installed put the bracket and cover back on and you're good to go.


And of course the pic of the old filter.


Looks like the date says 21.11.00. I guess it was long over due. At least it didn't say 1994. I've gotten parts with dates a couple years old, but either way that's at least 8 or 9 years. Not exactly the standard fuel filter interval! With the oil change and fuel filter done the car actually seems to pull a lot harder. Next is brake flush and power steering leak fix and flush.

Oil Change 1/16/2010

Mileage: 136900
Oil: Total Quartz Synthetic 10w50

I finally got around to changing the oil last week. The previous owner was running 15w40 Rotella-T Diesel non-synthetic oil. At first I was like wtf? I then read some post on bimmerforums and I guess the forum fan boys tend to use this stuff because it keeps the vanos unit from being so loud. Eh...I'd rather run synthetic. I chose the 10w50 based on price and it being heavier than a normal weight oil but not super heavy. It was around $30 for 5L from RMeuropean. No tax, no shipping! Here's a pic of the old shit.


Here's a pic of the new shit!


Having just bought the M3 and only having one garage/carport spot, I had to get the e30 buttoned up and out of the driveway. It's on a steep incline so pushing it in and out wasn't really an option. Here's some pics of how the e30 sits right now.






Onto the oil change. There is no reason really to write a DIY on the e36 oil change being that it is the easiest thing on the planet. The oil filter is positioned up instead of down on the top side of the engine. It's the silver casing that looks like an oild filter would be inside.


I didn't have any under panel, and I'm not sure if the under panel even blocks the drain plug. Regardless, steps are drain oil, remove the filter cap and replace the filter, replace the o-rings, close everything up and fill it up. Torque the oil filter housing bolt and drain bolt both to 18 ftlbs.

New filter ready to go in.


Here's a nice tutorial pic of removing the little o-ring on the bottom of the oil filter cap screw.


And a pic of me using a funnel.


I asked the PO when he changed the oil last and he said 135k. I didn't really want to take any chances plus I feel better now that I know what oil is in there. I filled it up to 6.5L like the manual calls for. It was where it needs to be on the dipstick. I've heard of running more oil for the track. I might decide to do that later. Either way this blog is more of evidence of the maintenance done to the car when a tutorial isn't really necessary!

Friday, December 18, 2009

Windshield Repair

So here's a picture of what my windshield was doing. Those are my fingers coming through from the interior. The whole driver's side of the windshield was pretty much coming up from the seal. Besides being a huge safety hazard there was terrible wind noise in the cabin anywhere above 40 mph.


I called a few places and Safelite said they would try and save the glass and repair it for $75, but no guarantees that the glass wouldn't break. If it did break I would have to pay for the full replacement price of $200. I figured that's fair and set up for a replacement on Thursday. I was in for the $200 but was hoping for the best.


Glass Removal. The safelite tech Walter was pretty cool and did a good job. He was able to just void the receipt for the replacement glass and reuse my old one! I was stoked. It was pretty new and it looked like it was just replaced, only not installed right....


M3 without a windshield pic. So this is the second time that the first thing I've done to my new car is replace the windshield. Driving my TT home from the dealer 2 years ago resulted in a cracked window. What's the deal?


Walt prepping the old glass.

Funny thing about this whole repair was that the previous owner had mounted an XM radio deep up in the front of the dash. You can see the residue from the sticky pad in this picture. The only way I was going to get that off cleanly was, well, by removing the windshield! Funny how things work out. Felt so good to get that nasty thing off.


In the end worked out $25 cheaper than if I would've made up some bs to State Farm. So I was happy paying only $75.


Of course I forgot to take a picture when it was done or go over anything interesting about window sealant and primer and all the tools that he used to remove it. Nothing changed in the appearance but now its just installed correctly this time and that little sticky pad is gone! Overall I was happy with Safelite and there is a lifetime warranty on the workmanship for the time that I own the car.

Sunday, December 13, 2009

Manual HVAC Bulb Replacement (1995)

So I had heard the 1995 m3 HVAC controls were basic compared to the later models. When I first drove the car back from San Diego the main knobs did not illuminate. I thought, man that is basic. I then realized that there was a light back there like any car to light up the knobs. This is a very easy DIY. It's actually a little more difficult in say the mkIV Jetta where you have to be very careful removing and installing the bulb. This car? not so much....

Part # Bulb: 63-21-7-167-000

I believe this is a pretty common bulb. You could probably take it out and go to Autozone and match it up. I got mine at BMA parts.

Picture of the small lights coming on but the main console not illuminating.


First step just pull the knobs off. They don't have to be in a particular position. They come off pretty easy. Don't worry about mixing up the different knobs. They are two of the same.


You'll see two philips head screws. Remove those.


Now use something plastic to pop the face out. Don't use a flathead screwdriver or something metal that will mess the face up. The small buttons will stay put.


Picture of the busted light.


This picture is pretty lame, but that's a Q-Tip in that little grated hole. After I cleaned that out I blew it with some compressed air. I'm not sure what the sensor behind there does, but I believe it measures the ambient temperature for the auto mode....which the 95 doesn't have.


Now simply pull the bulb out with your fingers and put the new one in there. It was so simple I didn't take pictures. Other cars I've done, where the bulb is stubborn, I've had to cut a small slit in a piece of fuel hose to secure the bulb while pressing it into it's base. You could also be very careful with some needle nose pliers, but for this car you can simply use your fingers.


Once you plug the new bulb in, test it before buttoning everything back up. But it should look like this when you're done. Yay light!

Cabin Filter Replacement

The cabin filter is one of the first things I replace when buying a used car. Who knows what kind of crazy shit is locked up in there. The e36 is also notorious for having a very weak air output when the filter is dirty. I picked the paper filter up at BMA Parts for $12.95 or something around there. I'm not sure if the dealer is charcoal, I didn't really care.

I used this tutorial as my guide:

Cabin Filter DIY
Part # Microfilter: 64-11-9-069-895

It's pretty detailed. I don't have too much to ad except for the fact that you cannot simply just pull out the old filter and put in the new one. There are blocks of wiring connectors interfering with a smooth installation of the filter. On the filter there are areas that you can crack so that the filter bends. I had to basically fold the thing in a tri-fold to get it in there. Once it's in, it's in though. I can't imagine a way of getting it in there without bending or folding it.


Particular to my car, there were no screws holding the kick panel in. It's pretty wedged in there so I guess there is no need really for the screws. Also when taking the panel down I noticed the dealer installed keyless entry! I didn't get the remote for this in the sale. I will probably call BMW and see if they can fashion me a new one based off the serial number on the unit.


I also took the time to remove the XM satellite radio antenna which was glued to the dash and wired under here.


The infamous old filter vs. new filter shot. It's possible that it's a carbon filter, but either way it was dirty as hell and had a bunch of old leaves trailing behind it.

Bought an M3


So I bought a 1995 Cosmos M3 down in San Diego on 12/5/09. I want to keep a running blog of everything I do to the car. I paid $5800 for the car which I thought was fair considering it was in pretty decent shape for being 15 years old and having 136k miles. A lot of the typical things that go wrong with e36's need attention, but things like the coolant system, struts and other bits and pieces have already been taken care of from the previous owner. A/C works all the electronics work, everything works and it has Vaders! I wasn't going to buy an m3 without those seats. Now I just have to tackle all the little annoyances and maintenance that is probably long overdue is some departments.

Story is, I went down to check out an e28 some guy wanted $6k for. I figured there is no way this thing is worth that much so I took out $4800 cash from the bank to go see it. Long story short, he had resprayed it and it no longer looked that good to me. He thought it did. I had this cash burning a hole in my pocket. I looked up 1995 m3s on my iphone and came across one that was $6500. I went to go check it out. It was getting late, I went with my gut, borrowed a G from Jin and bought the car on the spot. Here are some photos from the for sale ad.